共找到 150 條與 背壓檢漏法 相關的標準，共 10 頁
本標準規定了壓水堆燃料棒（以下簡稱“燃料棒”）密封性能氦質譜檢漏的方法以及檢測結果的計算和判定。 本標準適用于燃料棒的密封性能檢測，檢測泄漏率范圍為1×10-11Pa?m3/s～1×10-7Pa?m3/s。 壓水堆控制棒、可燃毒物棒、中子源棒等的氦質譜檢漏
Helium leak testing of nuclear fuel rod for PWR
本標準規定了重水堆核電廠燃料棒束的密封性能無損檢測的方法提要、材料與設備、檢驗條件、檢測步驟和檢測結果判定等內容。 本標準適用于重水堆核電廠燃料棒束密封性能的檢測，也適用于重水堆核電廠燃料元件密封性能的檢測。可檢測泄漏率范圍為1*10-11Pa·m3/s～1*10
Helium leak testing of PHWR nuclear fuel bundles
本標準規定了使用氦質譜檢漏技術對壓水堆燃料棒（以下簡稱“燃料棒”）密封性能進行無損檢測的方法、步驟和檢測結果的計算與判定。 本標準適用于壓水堆燃料棒的密封性能檢測，檢測泄漏率的范圍為1×10-11Pa·m3/s～1×10-7，Pa·m3/s。 本
Helium leak testing of nuclear fuel rod for PWR
本標準規定了航空用電子元器件密封性檢測的環境要求、人員要求、檢測方法選用原則、儀器設備要求、檢測原理、檢測條件、檢測程序、失效判據等。 本標準適用于內腔容積為1×10-2cm3～20cm3的航空電子元器件在生產、篩選、驗收和破壞性物理分析等過程中的密封性試驗，也適用于電
Leak test method for sealing of aviation components
本標準規定了氦質譜儀背壓檢漏的設備、環境、安全、人員、試驗原理、試驗程序的要求。 本標準適用于漏率在10-6Pa?m3/s～10-10Pa?m3/s的小型封閉產品的氦質譜儀背壓泄漏的檢測
Test methods for leaks using the helium mass spectrometer leak detector in the inside-out testing mode
Helium Mass Spectrometry Positive Pressure Leak Detection Method
This document describes the techniques for the determination of the leakage rates across the boundary of an isolated object, subjected to a pressure
Non-destructive testing - Leak testing - Pressure change method
Non-destructive testing - Leak testing - Pressure change method
Non-destructive testing - Leak testing - Pressure variation method
Non-destructive testing - Leak testing - Pressure change method
Non-destructive testing - Leak testing - Pressure variation method
Non-destructive testing - Leak testing - Pressure change method
ADOPTED_FROM:EN 13184:2001 This standard describes the techniques for the determination of the rate of leakage across the boundary of an isolated
Non-destructive testing — Leak testing — Pressure change method
This standard describes the techniques for the determination of the leakage rates across the boundary of an isolated object, subjected to a pressure
Non-destructive testing - Leak testing - Pressure change method
This standard describes the techniques for the determination of the leakage rates across the boundary of an isolated object, subjected to a pressure
Non-destructive testing - Leak testing - Pressure change method
