共找到 150 條與 能量校正 相關的標準，共 10 頁
本標準規定了俄歇電子譜儀動能標不確定度為3 eV時的校準方法,用于識別表面常規元素。另外,還規定一種用于確定校準周期的方法。本標準適用于直接模式或微分模式的儀器分辨率小于等于0.5%,微分模式調制幅度的峰峰值為2 eV。本標準適用于配有惰性氣體離子槍或其他樣品清潔方法,具有4 keV或更高束能電子槍
Surface chemical analysis.Medium resolution Auger electron spectrometers.Calibration of energy scales for elemental analysis
本標準規定了彈簧驅動的沖擊試驗器的結構，使用及其校正。 本標準適用于通過對被試樣品進行沖擊來檢驗電氣設備的機械強度的彈簧驅動的沖擊試驗器
Spring Driven Shock Tester and Its Calibration
本標準規定了用大面積2π多絲流氣式正比計數管絕對測量。發射率的原理、裝置、方法及數據處理等。 本標準適用于面積不大于170mm×120mm，且α粒子發射率在1×10s-1～1×104s-1（2πSr）范圍的α平面源
Measurment of emission rate of α particle. Method for large area proportional counter
本標準規定了用大面積流氣式2π多絲正比計數管絕對測量α粒子發射率的原理、裝置、方法及數據處理等。 本標準適用于面積不大于170mm×130mm，且α粒子發射率在1×10s-1~1×104s-1~（2πsr）范圍的α平面源。 本標準也可作為β粒子發射率測量的參考
Measurement of emission rate of α particle. Method for large area proportional counter
This standard provides a mechanism for promoting confidence in calibration laboratories and measuring and test equipment when it can be shown
Calibration -- Calibration Laboratories and Measuring and Test Equipment -- General Requirements
This Section of BS 7825 provides schedules for the calibration of a range of methods of test used for the evaluation of the thermal properties
Calibration of rubber and plastics test equipment - Calibration schedules - Thermal properties
? ??? ???? ??? ???? ??? ?? ??(1)? ??? ?? ? ??? ??
Measurement-General rules for calibration system
Przedmiotem normy s? znaki korektorskie oraz wytyczne wykonywania korekty drukarskiej
Correction signs and execu?iono? correction
Petroleum measurement systems - Calibration - Temperature corrections for use when calibrating volumetric proving tanks.
Establishes requirements for methods of measuring the alignment of crane wheels in accordance with ISO 4310 (published in South Africa as an identical
Cranes - Measurement of wheel alignment
?? ? ??? ?? ???? ??? ??? ???? ?? ?? ??? ?? ????
Petroleum measurement systems-Calibration-Temperature corrections for use when calibrating volumetric proving tanks
This International Standard specifies multiplication factors for the correction of the volume of water transferred from a primary measure to a tank
Petroleum measurement systems - Calibration - Temperature corrections for use when calibrating volumetric proving tanks
Petroleum measurement systems－Calibration－Temperature corrections for use when calibrating volumetric proving tanks
Practice for characterization and performance of a high-dose radiation dosimetry calibration laboratory
Liquid hydrocarbons. Dynamic measurement. Proving systems for volumetric meters. Part 4 : guide for operators of pipe provers
